img

Self-Leveling Sealant for OEMs

The third part of Dicor’s three-part roofing system, EPDM Lap Sealant creates a secure, secondary seal along the roof’s edges, air vents, vent pipes and screw heads. Compatible with EPDM and TPO sheeting, it adheres firmly to aluminum, mortar, wood, vinyl, galvanized metal, fiberglass and concrete. It is primarily used to fill voids and joints around vents, pipes or other penetrations through the membrane.

See All SKUs

Category:

Color matched (see below for colors and available sizes), the EPDM lap sealant is UV stabilized to prevent deterioration and discoloration. It will not stain or discolor any material to which it is applied.  DO NOT USE as splicing cement or on vertical surfaces.

This family of lap sealant is available only to OEM”s in single tube(s), 5 gallon or 55 gallon containers.  NOTE:  5  gallon and 55 gallon containers require a delivery system i.e., pump to dispense product.

Sealant Color Options:

Due to color variances across devices, actual colors may vary.

Self-Leveling (for horizontal surfaces)

Part Number Size Color
502LSD 10.3 oz. Tube
5 Gal. Pail
50 Gal. Drum
Dove (Bright White)
502LSG 10.3 oz. Tube
5 Gal. Pail
50 Gal. Drum
Grey
502LST 10.3 oz. Tube
5 Gal. Pail
50 Gal. Drum
Tan
502LSV 10.3 oz. Tube
5 Gal. Pail
50 Gal. Drum
Ivory
502LSW 10.3 oz. Tube
5 Gal. Pail
50 Gal. Drum
White

 

 

 

 

 

Additional information

Weight 1.2 lbs
Dimensions 11.25 × 2 × 2 in

Prior to application, clean the surface of all foreign materials.  Allow surface to dry.  Use standard caulking equipment to apply Self-leveling Sealant.  In cold weather, warm container at room temperature 60° (16°C) – 80° (27°C).

DO NOT USE on vertical surfaces. DO NOT USE as splicing cement.  Contains Naphtha.

Directions for Use:
Clean surface of all dirt, loose paint, rust, oil and grease. Allow surface to dry before applying sealant. Use standard caulking gun or pumping system to apply sealant. In cold weather, warm container at room temperature before use.

Caution: Keep away from heat, sparks and flame. To avoid breathing vapors, open windows and doors or use other means to insure fresh air entry during application and drying. If you experience eye watering, headaches or dizziness, increase fresh air or wear respiratory protection (NIOSH/MSHA TC23C or equivalent) or leave area. Causes nose, throat, eye and skin irritation.

Spills: Keep container closed when not in use. In case of spillage, absorb with inert material and dispose of in accordance with applicable regulations.

In Case of Fire: Use water spray, foam, dry chemical or carbon dioxide. Do not use a solid stream of water because it can scatter and spread the fire. Vapors are heavier than air and may travel along the ground to distant ignition sources and flash back.

First Aid: If swallowed, do not induce vomiting. Call a physician immediately. If inhaled, remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Glasses or goggles are recommended. In case of eye contact, immediately flush eyes with plenty of water of at least 15 minutes. Chemically resistant gloves recommended. In case of skin contact, thoroughly wash affected area with soap and water.

Health Notice: Reports have associated repeated and prolonged occupational overexposure to solvents with permanent brain and nervous system damage. Intentional misuse by deliberately concentrating and inhaling the contents may be harmful and fatal.

Click here for downloadable SDS sheet for 502LSD.

Click here for downloadable SDS sheet for 502LSG.

Click here for downloadable SDS sheet for 502LST.

Click here for downloadable SDS sheet for 502LSV.

Click here for downloadable SDS sheet for 502LSW.